Productos CUVIDASA | Rodamientos, correas y juntas

Productos

ref.

COP.01 C 200 EX

Bearing housing (unclassified)

Los cartuchos tipo EX alojan rodamientos de rodillos cilíndricos de dos piezas SKF Cooper no fijos (tipo EX). Proporcionan un asiento giratorio entre el rodamiento y el soporte exterior (que puede ser de pie, de pestaña o de otro tipo) para permitir la desalineación estática entre el eje y el soporte exterior. Los cartuchos también alojan sellos. El asiento giratorio permite que estos sellos se mantengan en concentricidad precisa con el eje para un sellado confiable.

ref.

TXL 524

Bearing housing (unclassified)

These seals provide effective sealing against many contaminants and allow for some grease to be purged when relubricating the bearing. Benchmark testing has proven low friction and outstanding service life. In highly contaminated environments, they provide the first barrier in a three-barrier solution. When ordering, please note that one item (seal pack) contains two seals (pre-cut).

ref.

ASNH 518-615

Bearing housing (unclassified)

End covers can be used at the end of shafts instead of seals. These end covers are made of polypropylene and designed for SNL bearing housings in sizes 05 to 32. They have good resistance to most chemicals and can withstand operating temperatures up to 110 °C (230 °F). End covers are easy to install and cost-effective accessories.

ref.

TSN 314 S

Bearing housing (unclassified)

SNL housing seals are the first barrier against contamination. For applications where there are high speeds or extreme temperatures, SKF recommends using labyrinth seals, and for highly contaminated environments, SKF recommends the three-barrier solution. This cost-effective sealing solution can have a significant impact on bearing service life as contaminants have to pass through three barriers to reach the bearing.

ref.

FRB 10/340

Bearing housing (unclassified)

Un rodamiento en la posición fija debe estar asegurado axialmente en el soporte. Si el asiento del rodamiento en el soporte y el ancho del rodamiento no coinciden, se necesitan aros de fijación (estabilizadores). Normalmente, se necesitan dos aros de fijación por soporte. Se debe colocar un aro en cada lado del rodamiento. Si solo se requiere un aro de fijación, debe instalarse en el mismo lado que la tuerca de fijación.

ref.

TSO 528

Bearing housing (unclassified)

These oil seal kits fit SONL housings. The stationary labyrinth ring and the rotating shaft sleeve form a narrow, multi-stage labyrinth. The seals are designed to drain oil back to the oil sump that has passed through the labyrinth. An oil pick-up ring is included in the kits, which can enhance the effect of oil bath lubrication.

ref.

TFL 512

Bearing housing (unclassified)

These seals provide low friction, effective sealing against many contaminants, and accommodate axial displacement of the shaft. In highly contaminated environments, they can serve as the first barrier in a three-barrier sealing solution. The combination of housing seals, the grease fill in the housing, and a bearing with integral seals can have a significant impact on bearing service life.

ref.

COP.02 C 5 GR

Bearing housing (unclassified)

Los cartuchos tipo GR alojan rodamientos de rodillos cilíndricos de dos piezas SKF Cooper de fijación (tipo GR). Proporcionan un asiento giratorio entre el rodamiento y el soporte exterior (que puede ser de pie, de pestaña o de otro tipo) para permitir la desalineación estática entre el eje y el soporte exterior. Los cartuchos también alojan sellos. El asiento giratorio permite que estos sellos se mantengan en concentricidad precisa con el eje para un sellado confiable. Los cartuchos de tipo GR utilizan tornillos axiales para sujetar el anillo exterior del rodamiento.

ref.

TXL 526

Bearing housing (unclassified)

These seals provide effective sealing against many contaminants and allow for some grease to be purged when relubricating the bearing. Benchmark testing has proven low friction and outstanding service life. In highly contaminated environments, they provide the first barrier in a three-barrier solution. When ordering, please note that one item (seal pack) contains two seals (pre-cut).

ref.

TSN 530 S

Bearing housing (unclassified)

SNL housing seals are the first barrier against contamination. For applications where there are high speeds or extreme temperatures, SKF recommends using labyrinth seals, and for highly contaminated environments, SKF recommends the three-barrier solution. This cost-effective sealing solution can have a significant impact on bearing service life as contaminants have to pass through three barriers to reach the bearing.

ref.

TS 48

Bearing housing (unclassified)

Los sellos de los soportes son la primera barrera contra la contaminación. Para aplicaciones en las que se producen altas velocidades o temperaturas extremas, SKF recomienda utilizar sellos laberínticos, y para entornos muy contaminados, SKF recomienda la solución de tres barreras. Esta solución de sellado rentable puede tener un impacto significativo en la vida útil del rodamiento, ya que los contaminantes tienen que atravesar tres barreras para llegar al rodamiento.

ref.

TSN 215 S

Bearing housing (unclassified)

SNL housing seals are the first barrier against contamination. For applications where there are high speeds or extreme temperatures, SKF recommends using labyrinth seals, and for highly contaminated environments, SKF recommends the three-barrier solution. This cost-effective sealing solution can have a significant impact on bearing service life as contaminants have to pass through three barriers to reach the bearing.

ref.

TFL 513

Bearing housing (unclassified)

These seals provide low friction, effective sealing against many contaminants, and accommodate axial displacement of the shaft. In highly contaminated environments, they can serve as the first barrier in a three-barrier sealing solution. The combination of housing seals, the grease fill in the housing, and a bearing with integral seals can have a significant impact on bearing service life.

ref.

COP.P15

Bearing housing (unclassified)

Los soportes de pie, también conocidos como pedestales, alojan cartuchos (soportes internos) para rodamientos de rodillos cilíndricos de dos piezas SKF Cooper y rodamientos de rodillos cónicos de dos piezas. Un asiento giratorio entre el soporte y el cartucho permite la desalineación estática entre el eje y las superficies de montaje del soporte. Los soportes de pie pueden utilizarse tanto para rodamientos fijos como libres.

ref.

TXL 528

Bearing housing (unclassified)

These seals provide effective sealing against many contaminants and allow for some grease to be purged when relubricating the bearing. Benchmark testing has proven low friction and outstanding service life. In highly contaminated environments, they provide the first barrier in a three-barrier solution. When ordering, please note that one item (seal pack) contains two seals (pre-cut).

ref.

ASNH 506-605

Bearing housing (unclassified)

End covers can be used at the end of shafts instead of seals. These end covers are made of polypropylene and designed for SNL bearing housings in sizes 05 to 32. They have good resistance to most chemicals and can withstand operating temperatures up to 110 °C (230 °F). End covers are easy to install and cost-effective accessories.

soluciones Técnicas

para el Mantenimiento Industrial

Brindamos una gama completa de soluciones técnicas, incluyendo diagnóstico avanzado, reparación, actualización de sistemas y asesoría técnica. Nuestro equipo de expertos está comprometido con ofrecerte soluciones personalizadas que se adapten a las necesidades específicas de tu operación, asegurando la máxima productividad y seguridad de tus instalaciones.